Car Maintenance
Showing 136–162 of 188 results
-
Add to cartMORE INFOWabtec Test Device Drawer
$856.96This shelf is specifically designed to hold the new Wabco Air Brake Test Device.- It is equipped with heavy duty locking drawer glides that allow the device to be extended a full 20”.
- May be mounted in a truck or utility vehicle to transport the device as needed for testing.
- The three piece design allows simple mounting.
-
Add to cartMORE INFOHitch Mounted Single EOTD Carrier For 2″ Receiver
$691.94- This carrier is used to transport any style EOTD using the standard 2” receiver commonly found on pickups and utility vehicles.
- Includes a nylon tie-down strap to keep the EOTD securely in place during transport, and an S hook to keep the hose in place.
- The holder swivels to a downward position to allow the vehicle tailgate to drop down while the holder is installed. Also available in a double holder configuration.
-
Add to cartMORE INFOHitch Mounted Double EOTD Carrier For 2″ Receiver
$996.89- This carrier is used to transport any style EOTD using the standard 2” receiver commonly found on pickups and utility vehicles.
- Includes a nylon tie-down strap to keep the EOTD securely in place during transport, and an S hook to keep the hose in place.
- The holder swivels to a downward position to allow the vehicle tailgate to drop down while the holder is installed.
-
Add to cartMORE INFOShort Slack Adjuster Transport Basket
$2,205.88- Use our new Slack Adjuster Transport Rack to store slack adjusters and ship them to the vendor for rebuilding.
- The bar grate flooring provides a strong surface that allows water and snow to pass through.
- May be handled either with a forklift or overhead lifting equipment.
- Length: 71″, Width 28″, Height 28″
-
Add to cartMORE INFOSlack Adjuster Transport Basket
$2,633.18- Use our new Slack Adjuster Transport Rack to store slack adjusters and ship them to the vendor for rebuilding.
- The bar grate flooring provides a strong surface that allows water and snow to pass through.
- May be handled either with a forklift or overhead lifting equipment.
- Length: 91″, Width 28″, Height 19″
-
Add to cartMORE INFORotating Head Hand Brake Lifter
$495.95- Use our new rotating hand brake fixture to remove or install wheel type freight car hand brakes.
- May be used with any overhead crane, hoist, or forklift equipped with a hook type lifting device.
- Includes standard lifting identiication tag.
- Equipped with a rotating mechanism that allows the hand brake to be removed in a vertical, balanced position even if the wheel mechanism is broken and jammed.
-
Add to cartMORE INFOForklift Torch Cart
$2,989.95- Use with any size forklift to transport gas bottles and cutting equipment around your repair facility. Also has lifting points to be moved with an overhead crane.
- The drop gates hold the bottles in place and provide ramps to remove and install the gas bottles.
- Holds up to a 9″ bottle on one side and up to a 12″ bottle on the other side
- Two toolboxes are included for storage of equipment and parts.
- A 50’ capacity spring take-up hose reel is also included.
-
Add to cartMORE INFOBrake Shoe Test Block
$184.92- The new 1 1/2″ Brake Shoe Test Block is designed to be placed between the brake shoe and the wheelset when performing freight car air brake tests.
- The block itself is made from High Strength Delrin plastic that will not crush or break as a result of the test pressures.
- The handle is made from light-weight alloy aluminum and includes a comfortable rubber handle for the operator.
-
Add to cartMORE INFOPry Bar Brake Shoe Test Block
$304.89• Our new 2″ thick Brake Shoe Test Block is designed to be placed between the brake shoe and the wheelset when performing freight car air brake testing.
• This new version of the Test Block includes a pry bar end that is specifically designed to push back brake shoes.
• The block itself is made from High Strength Delrin plastic that will not crush or break as a result of the test pressures.
• The handle is made from light-weight alloy aluminum and is knurled to provide a slip-resistant grip for the operator. -
Add to cartMORE INFOAluminum Hopper Gate Hand Wheel
$249.85- Use our new Hand Wheel to open or close Hopper Car Outlet Gates.
- The wheel is made of aluminum to keep the tool weight to a minimum (seven pounds).
- The fifteen inch diameter hand wheel provides the operator with leverage to open stubborn gates.
- The gate shaft is made of tool steel to provide a long-lasting contact surface.
-
Add to cartMORE INFOLift Table Trolley System
$9,745.88This rail mounted lift table is designed to remove and install Center Of Car and End Of Car Cushioning devices as well as draft gear assemblies. Comes equipped with a 110 volt, 3000 lbs. capacity hydraulic lift table with remote control and electric pinch point guard. Collapsed height is 12″ and extended height is 43″.
-
Add to cartMORE INFOLift Table Trolley System With Transfer Table
$11,859.71This version of our Lift Table Trolley System includes a Ball Transfer Table that allows two inches of left to right, and twelve inches front to rear movement for component positioning. The ball transfers are sealed and bolted to the table for easy replacement if damaged. The collapsed height is 14 1/2″ and the extended height is 43″.
-
Add to cartMORE INFOAluminum 8” Intermodal Car Side Sill Stands (Set Of Four)
$3,495.84Use our new Aluminum 8” Side Sill Stands to support intermodal car sections after they are separated to perform truck or coupler repairs. They are designed for use at facilities with paved floors that are even with the top of the rail. The aluminum construction keeps the weigh of the stand under 26 pounds. The durable heavy-duty rubber top eliminates metal-to-metal contact.
-
Add to cartMORE INFO
Aluminum 8” Intermodal Car Side Sill Stand (Single Stand)
$873.96Use our new Aluminum 8” Side Sill Stands to support intermodal car sections after they are separated to perform truck or coupler repairs. They are designed for use at facilities with paved floors that are even with the top of the rail. The aluminum construction keeps the weigh of the stand under 26 pounds. The durable heavy-duty rubber top eliminates metal-to-metal contact.
-
Add to cartMORE INFOAuto-Rack Coupler To End Sill Block
$399.89Use our new Auto-Rack Coupler To End Sill Block to maintain the proper spacing for the application of the deck bridge plates. Each block is equipped with handles for simple installation on the coupler and a heavy-duty strap to retain it on the coupler shank during use.
-
Add to cartMORE INFORail Wheel Mounted Ergonomic Swivel Chair
$3,139.92Our new Ergonomic chair is mounted on rail wheels to provide access for repairs under freight cars or locomotives. It is equipped with a swivel that provides 360 degrees of rotation, and glides that allow 30” of side-to-side movement. The back rest is fully adjustable, and features a gas strut to allow simple placement. Includes manual wheel brake and fire resistant cushion material.
-
Add to cartMORE INFOAir Brake Cylinder Tester
$2,998.87Our new testing system is designed to check any air brake cylinder for leakage. It was specifically designed to test both of the Wabcopac brake beam mounted cylinders. Simply charge the cylinder, place the control handle in the “Hold” position, and observe the built-in gauge to determine if the cylinder is leaking. Comes with a two-wheel cart, control system, and all necessary test hoses and connections.
-
Add to cartMORE INFODefective Wheel Set Handler
$2,289.94Use our new fixture to transport defective wheelsets to a testing facility for analysis. The base design allows the fixture to be handled with a forklift in any direction. A storage box is included to contain broken wheel sections or bearings. A holder is installed in the toolbox for related paperwork. Ratcheting two inch wide tie-down straps are included with the fixture.
-
Add to cartMORE INFOGas Bottle Holder For Truck Or Utility Vehicle
$1,283.78Use our new holder to transport fuel and oxygen bottles used for cutting and welding operations. The holder bolts to the bed, and has a lift-off segment for gas bottle replacement using a crane or hoist. The standard holder fits seven and eight inch bottles. Holders are available for other cylinder sizes.
